Відео

Got anything for gen 3 hemis?

Is there a big gap between the seat bracket and the floor? Mine have a big gap :(

Can you make a motor plate install video for SBF? Thanks

Could you bolt it in ?

Hi David. I purchased your LS swap k-member (for 90 fox) and A arm’s and was wondering if you could help me by telling me what all header’s work with your k-members now? I purchased the speed engineering headers and that was a big waist of money. Been researching for a week and was leaning towards the Hooker Blackheart header’s(even though they was probably way out my price range), only to find out they discontinued them🥲. And also would the Hooker Blackheart mount’s open up my header selection? Thanks 🙏

Lou!

This is such a great video. Enjoyed it immensely. Thank you

Nice video thanks!

Super high quality! I have bought from the more expensive competition before you and now only buy your parts after seeing the better quality and cost less!!!

When you weld on a tube it bends the tube. using heat or weld is how a bent tube is straightened he just gave the car toe out which is not good (it screws up the handling) at all if he had welded it on the front side he would have given it toe in which is fine. A clamp on bracket with the tab on the top or bottom would be the best, I work in a machine shop is how I know.

Are these strong enough that I can put a jack stand under each side while working on the car? (Foxbody) Thankyou team Z

No instructions included but the rear brake hose junction is now in the way and you may have to move it and/or bend up some new brake lines. The hardware supplied is short a few washers but those are easily accessed.

How are you fully welding pillars and eye brow bar? And roof notches. Dose this kit come in mild tubbing I don’t have a tig welder? Full cert on chrome molly is 8sec?

This kit is going on my 04 terminator this week! Can’t wait.

With the pro series kit will it help more with putting on the lower relocation bracket and move lower control arm from factory location

Unfortunately this wouldn't work with my exhaust set up..🥺

Jajaja jajaja jajaja jajaja

do you have cages for other cars for sale

Do you offer a kit for a 69 Torino/Fairlane?

Like how it’s not mentioned you have to grind down the fucking axle to get the bushings in

Do you make a cage kit for a 1966 Chevy II? If not, who's kit do you recommend? Thanks for any information.

You wouldn't happen to still have the trunk spring's I could buy? I just bout a 89 n some one took the springs off n Idk why, cause its heavy enough lol..

I run the relocated uppers and double adjustable lowers on my 2003 mustang. I have a stock rear spring cut one coil with the spring isolators installed and the ride height is about one finger gap with a 275 60 15 on a 15x10. I run a strange 10 way single adjustable rear shock and 10 way adjustable front coilover both on full loose on the street. The setup works great on the street. I can feel the rear separation and it stays up on the tire and keeps the front up and feels very stable and controlled on the street. My engine and pinion angle are set at -2.4

I remember that car proven... Ill always have love for Team Z

Do u guys make a cage for a first gen Camaro?

The shame he left on the blue focus shamed it entirely. 😂

1/1/2021 and still watching.

Magnets are a welders best friend

Dave, nice to see you're still getting it done! Great job!!!

How do you weld the top of the A pillar bar to the main hoop, as well as the windshield bar to the A pillar bars on the top side if using 6x6 plates.

I'm new to engine plates... do you use any sealant or gasket between the plate and the engine on the water pump holes? Or just straight bolt 0n?

Do you have anything thing for g body’s

Put some safety glasses on when using that grinder. 👮‍♀️

Yeah technology is awesome. Friday at work I was drilling a 21/64 hole at 15 in/min in 316 stainless.

NovaJoe will be ordering my stuff within a week or so,i am looking foward to adding all the stuff to my 84..🇺🇸

Why is there no audio?

How much weight saved? Will this plastic deck lid elliminator structure support Strutless wing? My hatch&glass feel like 150# on bad gas lift🤐

HAHAHA

You guys are fucking hacks. Prep your material and this shit is paper thin.

I took my old upper control arms off, and the bolt holes were no longer round... TeamZ with relocated uppers are waiting for me to put them on.

Buying the kit next week probably. I would like to say that Team Zs customer support is amazing. I asked for my spring height for my combo and instantly got my answer.

Did anyone have a problem with the motor mount bolts lining up???

Fire the camera clown.

Got to square the k member front to back

Do you guys still offer this 2 piece deck lid?

With doing a motor plate and mid plate, does it help with preventing block twisting?

Do you make one or can you for the SN95? thanks

Does team z offer install of there products to customers ?

2011 seems so so long ago....just saying lol

Do you do cage installation if the customer wants this option?